Herramientas Destacadas en este Teardown

Introducción

Going to take apart my Power Mac 8600/250!

Tools:

#1 Phillips screwdriver

Spudger/Flathead screwdriver

Your hands!

Este desmontaje no es una guía de reparación. Para reparar tu Power Macintosh 8600(250), utiliza nuestros manuales de servicio .

  1. There she is! i'm missing the bezel around the floppy drive :(
    • There she is! i'm missing the bezel around the floppy drive :(

    Agregar Comentario

  2. Start by pressing the big green button. And pulling the door away and up from the computer.
    • Start by pressing the big green button. And pulling the door away and up from the computer.

    • And on the Back of the door is the fan.

    Agregar Comentario

    • Now it's best to lay the computer flat.

    • And to flip up the tabs, grab the handle and open.

    Agregar Comentario

    • The innards, motherboard, daughter board, RAM and so fourth.

    Agregar Comentario

    • Now the speaker

    • Remove the speaker wires

    • And the fan wires from the motherboard

    • Push in the two plastic tabs on either side and lift the speaker up and out.

    Agregar Comentario

  3. Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    • The PRAM battery!

    • Remove the housing by pulling it out and then take the battery out.

    Agregar Comentario

    • The processor, firmly grasp and pull out.

    • Remove the 4 #1 Phillips screws

    • And push the 4 tabs off of the board

    High failure rate - these bassas’

    Mal - Contestar

    • Any video card or usb card, mine happens to be an ethernet 10/100 card.

    • Unfortunately there are 6 spaces but only 3 slots on the motherboard :(

    • Remove the #1 Phillips screw and pull the card out.

    Agregar Comentario

    • RAM and VRAM slots!

    Agregar Comentario

    • Moving on to the CD, ZIP, and Floppy drives (best to close computer now)

    • Remove the bezels and if I had the top one remove that too.

    • Remove the 6 phillips screws and pull the metal frames out.

    Agregar Comentario

    • Remove the data and power cables

    • Pay special attention to this one, it has a clip on it, it helps to use a flathead or a spudger.

    • Pull the drives out of the bay.

    Agregar Comentario

    • Now the hard drive.

    • Remove the two phillips screws

    • And the data and power cables (might help to remove them as you pull the drive out)

    Agregar Comentario

    • The power source

    • Remove the two connectors

    • There is a clip holding the wires in place. Separate and remove the wires. (both sets)

    Agregar Comentario

    • Now remove the 4 phillips screws (it's best to start with the bottom two)

    • And pull it out while de-threading the wires.

    Agregar Comentario

Plague

Miembro Desde 14/06/10

171 Reputación

1 Guía escrita

Nice. I got a beige G3 300 Mhz, the case is similar. Maybe I could also make a teardown.

Nicolas Zbinden - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 3

Últimos 30 Días: 23

Todo El Tiempo: 13,383