Saltar al contenido principal

Qué necesitas

Este desmontaje no es una guía de reparación. Para reparar tu Power Mac G4 M5183, utiliza nuestros manuales de servicio .

  1. Power Mac G4 M5183 Teardown STEM Project, Case: paso 1, imagen 1 de 2 Power Mac G4 M5183 Teardown STEM Project, Case: paso 1, imagen 2 de 2
    • Pull the tab to open the case.

  2. Power Mac G4 M5183 Teardown STEM Project, RAM: paso 2, imagen 1 de 2 Power Mac G4 M5183 Teardown STEM Project, RAM: paso 2, imagen 2 de 2
    • Pull the white tabs down

    • Lift up the RAM

    • Repeat x4

  3. Power Mac G4 M5183 Teardown STEM Project, Heat-sink: paso 3, imagen 1 de 2 Power Mac G4 M5183 Teardown STEM Project, Heat-sink: paso 3, imagen 2 de 2
    • Use a flat head screwdriver or spudger to lift up the tabs that hold down the heat-sink.

    • Repeat x2

    • The heat-sink should just lift right off.

  4. Power Mac G4 M5183 Teardown STEM Project, GPU: paso 4, imagen 1 de 2 Power Mac G4 M5183 Teardown STEM Project, GPU: paso 4, imagen 2 de 2
    • Remove highlighted screw.

    • The GPU should lift right out.

  5. Power Mac G4 M5183 Teardown STEM Project, Mother Board: paso 5, imagen 1 de 3 Power Mac G4 M5183 Teardown STEM Project, Mother Board: paso 5, imagen 2 de 3 Power Mac G4 M5183 Teardown STEM Project, Mother Board: paso 5, imagen 3 de 3
    • Remove highlighted cables.

    • Remove highlighted screws.

    • Lift out the motherboard. (Note: pull to the left to clear the ports from the case)

  6. Power Mac G4 M5183 Teardown STEM Project, CPU: paso 6, imagen 1 de 2 Power Mac G4 M5183 Teardown STEM Project, CPU: paso 6, imagen 2 de 2
    • Remove highlighted screws.

    • After removing the screws, simply lift off the CPU from the connector. Use only a minimal amount of pressure when pulling the CPU from the connector.

    • This is the connector after removal of the CPU.

  7. Power Mac G4 M5183 Teardown STEM Project, DVD/ROM drive: paso 7, imagen 1 de 3 Power Mac G4 M5183 Teardown STEM Project, DVD/ROM drive: paso 7, imagen 2 de 3 Power Mac G4 M5183 Teardown STEM Project, DVD/ROM drive: paso 7, imagen 3 de 3
    • Remove the face plate. You are supposed to press down the highlighted tabs from the inside.

    • Remove highlighted screws.

    • Slide out the drive. (MAKE SURE TO UNHOOK THE CABLES)

  8. Power Mac G4 M5183 Teardown STEM Project, Hard drive: paso 8, imagen 1 de 3 Power Mac G4 M5183 Teardown STEM Project, Hard drive: paso 8, imagen 2 de 3 Power Mac G4 M5183 Teardown STEM Project, Hard drive: paso 8, imagen 3 de 3
    • Remove the highlighted cables.

    • Remove highlighted screw.

    • Lift out the hard drive.

  9. Power Mac G4 M5183 Teardown STEM Project, Main Fan: paso 9, imagen 1 de 2 Power Mac G4 M5183 Teardown STEM Project, Main Fan: paso 9, imagen 2 de 2
    • Remove highlighted screw. ( SAME SCREW ON OPPOSITE SIDE, REMOVE THAT AS WELL.)

    • Disconnect the connector.

    • After that, just pull it out.

  10. Power Mac G4 M5183 Teardown STEM Project, Power Supply: paso 10, imagen 1 de 3 Power Mac G4 M5183 Teardown STEM Project, Power Supply: paso 10, imagen 2 de 3 Power Mac G4 M5183 Teardown STEM Project, Power Supply: paso 10, imagen 3 de 3
    • Use a 2.5 mm hex key to remove these screws.

    • Remove highlighted screw.

    • Feed the wires through the highlighted hole, then pull out the power supply.

  11. Power Mac G4 M5183 Teardown STEM Project, Finished!: paso 11, imagen 1 de 1
    • You will be left with an empty case.

Harrison Case

Miembro Desde 11/06/16

128 Reputación

1 Guía escrita

4 comentarios

Just a little tip.

APPLE tend to use screw connections as a means of ground continuity.

That is - if the CPU card is not screwed down - it might not power on.

Mal - Contestar

The is a kit from thelaserhive.com to allow an mATX board to be used inside the G4 cases.

Pete Karnowski - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 11

Ultimos 30 días: 46

Todo El Tiempo: 3,330