Herramientas Destacadas en este Teardown

Introducción

This teardown guide shows step-by-step how to take apart your PSP 3000

Este desmontaje no es una guía de reparación. Para reparar tu PSP 300x, utiliza nuestros manuales de servicio .

The first picture is a view of the front of the PSP-3000. The second picture is of the back.
  • The first picture is a view of the front of the PSP-3000. The second picture is of the back.

Agregar Comentario

Lift the covering from the left side on the back of the PSP to reveal the battery.
  • Lift the covering from the left side on the back of the PSP to reveal the battery.

  • Pull up on the top at the top of the battery with your fingernail and remove it.

Agregar Comentario

Agregar Comentario

  • Unscrew two screws from the top of the PSP.

  • Turn the PSP around, and unscrew a single screw from the bottom edge.

Agregar Comentario

  • Starting from the 'R' trigger, slide the spudger in between the outer casing the the PSP, and gently pry off the casing.

  • Remove the outer casing completely.

Agregar Comentario

  • Push the homebar to the right to release the tab on the right side of the LCD screen.

  • DO NOT completely remove the homebar, as it is still connected by ribbon cables.

  • Slowly begin to lift the LCD screen off the PSP from the top edge.

  • Again, the LCD screen is attached by ribbon cables, so do not remove it completely.

Agregar Comentario

  • Using a spudger or fingernail, flip the small brown locks on the four ribbon cable connectors up.

  • WARNING! Be carefull removing the small ribbion from the LCD connector, it is very delicate. Using a spudger lift the black plastic up, NOT the white part on the connector!

  • Pull all four ribbon cables out, and remove the LCD screen and homebar from the PSP.

Agregar Comentario

  • Remove the small metal bar from the top edge of the PSP. (This was helping to hold the LCD screen in place)

  • Remove the button pad from the PSP.

Agregar Comentario

  • Unscrew the the screw securing 'L' trigger.

  • Remove the white plastic piece that holds the 'L' trigger in place.

  • Remove the 'L' trigger from the PSP.

Agregar Comentario

  • Unscrew the 'R' trigger and remove both pieces. (Refer to step nine by applying the procedures to this, the right, side)

Agregar Comentario

  • Remove the screw from the bottom left edge.

  • Being careful not to break the ribbon cable, use the spudger, to carefully peel the adhesive button from below the 'L' trigger.

Agregar Comentario

  • Using the spudger or fingernail, flip up the brown lock on the ribbon cable.

  • Remove the cable from the connector and remove the entire black piece from the PSP.

  • Remove the screw from the analog stick.

Agregar Comentario

  • Unlock and remove the ribbon cable connection the analog stick to the main board.

  • Remove the analog stick from the PSP.

Agregar Comentario

  • Unlock and remove the ribbon cable from the power switch on the right side of the PSP.

  • Unscrew and remove the screw from the yellow power jack.

  • Carefully bend back the black tab holding the power jack in place and start pulling the plug up to release it from this clip.

Agregar Comentario

  • Pull the plug connecting the power jack to the motherboard.

  • Remove the power jack.

Agregar Comentario

  • Push the black tab at the bottom of the speaker over.

  • The speaker should pop out of place, and you should be able to remove it easily.

Agregar Comentario

  • Pull the wireless antenna cable from its plug.

  • Unlock and remove both ribbon cables from the mother board.

Agregar Comentario

  • Remove the screw from the power switch board.

  • Remove the power switch assembly/board.

Agregar Comentario

  • Unlock and remove one last ribbon cable from the bottom edge of the PSP.

  • Remove the screw from the bottom left corner of the PSP.

Agregar Comentario

  • Lift the silver rim on the right side of the PSP up and off.

  • Lift the silver rim on the left side of the PSP up and off.

Agregar Comentario

  • Lift the motherboard up slowly starting from the bottom of the PSP, being careful not to damage the port on top.

  • Pull the motherboard out and remove it from the PSP.

    • The specific motherboard model of this PSP-3000 is TA-090

Agregar Comentario

  • On the top of the back of the PSP, pull the white plastic piece out.

  • Pull the spring out and remove it from the PSP.

Agregar Comentario

  • Open the UMD (disk drive) and locate the two small black rubber squares wedged in the space between the casing and the metal drive hinge on either side.

  • Pull these out using a pair of tweezers.

Agregar Comentario

  • Remove the metal piece from the drive.

  • Grabbing the PSP with both hands, gently pinch the UMD lid towards the right side (the side without the battery).

  • Pull up and the the left side carefully to remove the lid from the PSP. (The casing may have to flex a little bit to allow this)

Agregar Comentario

  • Remove the four screw from the UMD drive.

  • Remove the drive.

Agregar Comentario

  • Enjoy the eye-candy.

for a change, user submitted teardown with Great quality photos, Awesome!

mahonen - Contestar

Awesome Job....... I never know that my PSP has a lot of things in it

Ummayer Rehan - Contestar

mbnewsom

Miembro Desde 28/10/09

2,399 Reputación

11 Guías creadas

Can you get me in pdf

Aayush - Contestar

Does a PSP have any bearings inside of it?

Brooke Payne - Contestar

No ball bearings. Thumbsticks are probably just Lubed plastics rubbing against eachother

mahonen -

Thank you very much for the guide.

C. JONES - Contestar

This has inspired me to build my own PSP. I had one as a child, and want one now for the nostalgia. Thanks!

Sheenyl Hassan - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 16

Últimos 7 Días: 106

Últimos 30 Días: 441

Todo El Tiempo: 47,384