Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Partes y herramientas

Resumen del Video

  1. Remove back cover. Moto G3 plastic panel can be easily removed with the fingernails.
    • Remove back cover.

    • Moto G3 plastic panel can be easily removed with the fingernails.

  2. Remove camera&flashlight metal cover. Use tweezers to cut strong adhesives underneath. Remove camera&flashlight metal cover. Use tweezers to cut strong adhesives underneath.
    • Remove camera&flashlight metal cover. Use tweezers to cut strong adhesives underneath.

  3. Undo 3 screws by T4 Torx screwdriver. Take away plastic securing part.
    • Undo 3 screws by T4 Torx screwdriver.

    • Take away plastic securing part.

  4. Heat up the LCD screen for a while. Then with the help of suction cup, insert guitar picks to open a gap. Slide guitar picks or plastic opening tool to cut strong adhesives. There is LCD screen connector on the left side, so be careful to slide guitar picks.
    • Heat up the LCD screen for a while.

    • Then with the help of suction cup, insert guitar picks to open a gap. Slide guitar picks or plastic opening tool to cut strong adhesives.

    • There is LCD screen connector on the left side, so be careful to slide guitar picks.

  5. Release LCD screen connector firstly. Remove LCD screen. Remove LCD screen.
    • Release LCD screen connector firstly.

    • Remove LCD screen.

  6. Undo 14 screws by T4 Torx screwdriver Pry up motherboard assembly. Battery flex connector is connected with motherboard, so be careful to pry the assembly up.
    • Undo 14 screws by T4 Torx screwdriver

    • Pry up motherboard assembly.

    • Battery flex connector is connected with motherboard, so be careful to pry the assembly up.

  7. Kits de Reparación de Pantalla LCD de iPhone

    La opción de presupuesto, cubierta por nuestra garantía de por vida.

    Compra kits

    Kits de Reparación de Pantalla LCD de iPhone

    Reduce los costos de reparación, no la calidad.

    Compra kits
  8. Release battery flex connector. Separate motherboard assembly from back cover assembly.
    • Release battery flex connector.

    • Separate motherboard assembly from back cover assembly.

  9. Undo 3 screws here. Use spudger to cut adhesives and pry the SIM&SD card reader board, then remove it. Use spudger to cut adhesives and pry the SIM&SD card reader board, then remove it.
    • Undo 3 screws here.

    • Use spudger to cut adhesives and pry the SIM&SD card reader board, then remove it.

  10. Remove front-facing camera. Remove front-facing camera.
    • Remove front-facing camera.

  11. Remove rear camera. Remove rear camera. Remove rear camera.
    • Remove rear camera.

  12. Remove earpiece. Remove earpiece.
    • Remove earpiece.

  13. Remove loudspeaker. Remove loudspeaker.
    • Remove loudspeaker.

  14. Here is the motherboard. Here is the motherboard.
    • Here is the motherboard.

  15. Use spudger to cut adhesive and pry the battery up. Use spudger to cut adhesive and pry the battery up.
    • Use spudger to cut adhesive and pry the battery up.

  16. Take away headphone jack. Take away headphone jack. Take away headphone jack.
    • Take away headphone jack.

  17. Done
    • Done

Linea de Meta

15 personas más completaron esta guía.

Witrigs

Miembro Desde 24/11/15

64,061 Reputación

386 Guías creadas

Muito bom, parabéns!

Manoel - Contestar

Could you guys tell me if the main speaker, at the bottom, has a special protection agains water spills, like a membrane or so, or is it pretty fine too spill water there?

setsuoleandro - Contestar

Wi fi not trun on ..moto g3

Seoni Seoni - Contestar

When you heat up the display, do you heat up the entire display or just around the edges? What heat gun/setting should i use? Can i use a blowdryer?

guest - Contestar

Thanks. ......................

Biswajit Saha - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 8

Ultimos 7 días: 38

Ultimos 30 días: 180

Todo El Tiempo: 19,456