Saltar al contenido principal

Qué necesitas

Este desmontaje no es una guía de reparación. Para reparar tu Lenovo ThinkPad 410, utiliza nuestros manuales de servicio .

  1. Este paso está sin traducir. Ayuda a traducirlo

    • Unlatch and remove battery

  2. Este paso está sin traducir. Ayuda a traducirlo

    • Open Acess panel

  3. Este paso está sin traducir. Ayuda a traducirlo

    • Remove Hard drive

  4. Este paso está sin traducir. Ayuda a traducirlo

    • Remove wirless WAN

  5. Este paso está sin traducir. Ayuda a traducirlo

    • Remove DIMM from back

  6. Este paso está sin traducir. Ayuda a traducirlo

    • Remove Keyboard retaing Screw from bottom of system

    • Turn the system over and open the cover. Push the keyboard toward the back and lift it up. Slide it forward to rest it on the palm rest. Disconnect the ribbon cable.

  7. Este paso está sin traducir. Ayuda a traducirlo

    • Remove BIOS battery

  8. Este paso está sin traducir. Ayuda a traducirlo

    • Disconnect the two antenna leads from the Wireless WAN card. Remove the two retaining screws. Rotate the card up and pull it out of the slot.

    • Remeber which lead goes where Prior to removing it . Grey is usually MAIN , black AUX

  9. Este paso está sin traducir. Ayuda a traducirlo

    • Remove 14 retaining screws from back

    • The first 9 are required for bezel and touchpad removal .

    • M2 × 14 mm, wafer-head, nylon-coated (6)

    • M2 × 3 mm, wafer-head, nylon-coated (3)

    • The remaining need to be removed for base cover removal

    • M2 × 5 mm, wafer-head, nylon-coated (4)

    • M2 × 10 mm, wafer-head, nylon-coated (1)

    • Note: The FPC cable is attached on the underside of the keyboard bezel assembly. In some models, the Bluetooth daughter card is also attached on the underside of the keyboard bezel assembly.

  10. Este paso está sin traducir. Ayuda a traducirlo

    • Turn system over , open , remove 4 retaining screws and the work form one side , using spudger to remove chasis bezel

    • M2 × 3 mm, wafer-head, nylon-coated (4)

  11. Este paso está sin traducir. Ayuda a traducirlo

    • Remove 4 retaining screws

    • M2 × 3 mm, wafer-head, nylon-coated (4)

  12. Este paso está sin traducir. Ayuda a traducirlo

    • Remove the two retaining screws on the bottom of the system.

    • M2.5 × 6 mm, wafer-head, nylon-coated (2)

    • Turn the system over and open the cover.

    • Unroute all the wires.

    • Remove the retaining screws.

    • M2.5 × 6 mm, wafer-head, nylon-coated (2)

    • Carefully lift the LCD panel up and out of the chass

kevinleroy

Miembro Desde 08/13/12

338 Reputación

1 Guía escrita

Equipo

Master Techs Miembro de Master Techs

Community

321 Miembros

1,485 Guías creadas

5 comentarios

Uhm, sorry, what about the photos? I don't see any...

JoeMuc2014 - Contestar

Still not seeing any photos accompanying the steps listed in the teardown.

Jason Landers - Contestar

well. if get short out inside of USB or network line>> that has been stopping the software lunched.

mohammed - Contestar

we need teardown of T410

mohammed - Contestar

The video shows a teardown of the T410s. It is a lot different from the T410.

Robert Oschmann - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 15

Ultimos 30 días: 55

Todo El Tiempo: 10,501