Resumen del Video

Introducción

Here is a video teardown of the ThinkPad T410s.

Below is a step by step teardown

Este desmontaje no es una guía de reparación. Para reparar tu Lenovo ThinkPad 410s, utiliza nuestros manuales de servicio .

    • Unlatch and remove battery

    Agregar Comentario

    • Open Acess panel

    Agregar Comentario

    • Remove Hard drive

    Agregar Comentario

    • Remove wirless WAN

    Agregar Comentario

  1. Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    • Remove DIMM from back

    Agregar Comentario

    • Remove Keyboard retaing Screw from bottom of system

    • Turn the system over and open the cover. Push the keyboard toward the back and lift it up. Slide it forward to rest it on the palm rest. Disconnect the ribbon cable.

    Agregar Comentario

    • Remove BIOS battery

    Agregar Comentario

    • Disconnect the two antenna leads from the Wireless WAN card. Remove the two retaining screws. Rotate the card up and pull it out of the slot.

    • Remeber which lead goes where Prior to removing it . Grey is usually MAIN , black AUX

    Agregar Comentario

    • Remove 14 retaining screws from back

    • The first 9 are required for bezel and touchpad removal .

    • M2 × 14 mm, wafer-head, nylon-coated (6)

    • M2 × 3 mm, wafer-head, nylon-coated (3)

    • The remaining need to be removed for base cover removal

    • M2 × 5 mm, wafer-head, nylon-coated (4)

    • M2 × 10 mm, wafer-head, nylon-coated (1)

    • Note: The FPC cable is attached on the underside of the keyboard bezel assembly. In some models, the Bluetooth daughter card is also attached on the underside of the keyboard bezel assembly.

    Agregar Comentario

    • Turn system over , open , remove 4 retaining screws and the work form one side , using spudger to remove chasis bezel

    • M2 × 3 mm, wafer-head, nylon-coated (4)

    Agregar Comentario

    • Remove 4 retaining screws

    • M2 × 3 mm, wafer-head, nylon-coated (4)

    Agregar Comentario

    • Remove the two retaining screws on the bottom of the system.

    • M2.5 × 6 mm, wafer-head, nylon-coated (2)

    • Turn the system over and open the cover.

    • Unroute all the wires.

    • Remove the retaining screws.

    • M2.5 × 6 mm, wafer-head, nylon-coated (2)

    • Carefully lift the LCD panel up and out of the chass

    Agregar Comentario

kevinleroy

Miembro Desde 13/08/12

326 Reputación

1 Guía escrita

Equipo

Master Techs Miembro de Master Techs

Community

279 Miembros

758 Guías creadas

Uhm, sorry, what about the photos? I don't see any...

JoeMuc2014 - Contestar

Still not seeing any photos accompanying the steps listed in the teardown.

Jason Landers - Contestar

well. if get short out inside of USB or network line>> that has been stopping the software lunched.

mohammed - Contestar

we need teardown of T410

mohammed - Contestar

The video shows a teardown of the T410s. It is a lot different from the T410.

Robert Oschmann - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 2

Últimos 7 Días: 12

Últimos 30 Días: 53

Todo El Tiempo: 6,656