Saltar al contenido principal

Qué necesitas

Este desmontaje no es una guía de reparación. Para reparar tu Belkin WeMo Switch, utiliza nuestros manuales de servicio .

  1. Belkin WeMo Switch Teardown, Belkin WeMo Switch Teardown: paso 1, imagen 1 de 2 Belkin WeMo Switch Teardown, Belkin WeMo Switch Teardown: paso 1, imagen 2 de 2
    • Model: F7C027

    • FCC ID: K7SF7C027

    • Input: 120 V, 15 A, 60 Hz

    • Output: 120V, 15 A, 60 Hz

  2. Belkin WeMo Switch Teardown: paso 2, imagen 1 de 2 Belkin WeMo Switch Teardown: paso 2, imagen 2 de 2
    • Remove the four 11.9 mm triangle screws securing the two halves of the case together.

    • The upper two screws are hidden underneath the label, so you'll need to cut away the sticker directly above the screws.

  3. Belkin WeMo Switch Teardown: paso 3, imagen 1 de 2 Belkin WeMo Switch Teardown: paso 3, imagen 2 de 2
    • Carefully pry the back case off.

  4. Belkin WeMo Switch Teardown: paso 4, imagen 1 de 1
    • Remove the two 9.9 mm Phillips #1 screws securing the power board to the device.

  5. Belkin WeMo Switch Teardown: paso 5, imagen 1 de 1
    • Use a pair of tweezers to disconnect the power plug from the motherboard.

  6. Belkin WeMo Switch Teardown: paso 6, imagen 1 de 2 Belkin WeMo Switch Teardown: paso 6, imagen 2 de 2
    • Remove the power board from the device.

  7. Belkin WeMo Switch Teardown: paso 7, imagen 1 de 3 Belkin WeMo Switch Teardown: paso 7, imagen 2 de 3 Belkin WeMo Switch Teardown: paso 7, imagen 3 de 3
    • Use the flat end of spudger to gently pry the retaining flaps away from the motherboard.

    • The motherboard should now come free.

  8. Belkin WeMo Switch Teardown: paso 8, imagen 1 de 2 Belkin WeMo Switch Teardown: paso 8, imagen 2 de 2
    • Components on the motherboard:

    • Ralink RT5350 Wi-Fi SoC

    • Winbond W9825G6JH-6 256 Mb 166 MHz SDRAM

    • Macronix MX25L12835EMI-10G 128 Mb NOR Flash Memory

    • Momentary push button switch for factory reset

    • Momentary push button switch for power switch

  9. Belkin WeMo Switch Teardown: paso 9, imagen 1 de 2 Belkin WeMo Switch Teardown: paso 9, imagen 2 de 2
    • Components on the power board:

    • Hongfa HF3FA 10 A Relay

    • Power Integrations LNK606DG 5.5 W AC/DC Converter

    • TAICON 6.8 µF Capacitor (x2)

    • FOAI 680 µF Capacitor (x2)

    • JOYIN JVR10N471K 385 V 70 J Varistor

    • Chipsen EPC13 50 W Transformer

    • PANJIT International TB8S 800 V 30 A Bridge Rectifier Diode

  10. Belkin WeMo Switch Teardown: paso 10, imagen 1 de 1
    • Final layout.

Geoff Wacker

Miembro Desde 09/30/13

89,846 Reputación

89 Guías creadas

4 comentarios

I notice that’s a 240V 10amp relay they’ve used. Do you think there is any electrical difference (aside from the plug pattern) between the US 110V version and the EU/Australian 220V one?

Greg Bromage - Contestar

Thank you, that was a big help! The exterior on off button had come loose and was rattling around inside and I was able to repair it thanks to your tear down guide.

L Threet - Contestar

A T-7 torx screwdriver works well if you don't have the 2mm triangle

olaf - Contestar

Thanks, also here 2 of them after little use: The exterior on off button had come loose and was rattling around inside. Very poor quality now I have opened them. Guess need to try and glue them back on.

Helmuth van Es - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 8

Ultimos 30 días: 24

Todo El Tiempo: 9,857